specification model eln-30-5 eln-30-9 eln-30-12 eln-30-15 eln-30-24 eln -30-27 eln-30-48 dc voltage rated current current range rated power output voltage adj. range current adj. range line regulation load regulation setup, rise time note.6 hold up time (typ.) voltage range note.4 frequency range efficiency (typ.) ac current (typ.) input inrush current (max.) leakage current safety standards working temp. dimming control (optional) working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing over current over voltage 5v 9v 3 ~ 9v 12v 3 ~ 12v 15v 3 ~ 15v 24v 3 ~ 24v 27v 3 ~ 27v 48v 3 ~ 48v 5a 3.4a 2.5a 2a 1.25a 1.12a 0.63a 0 ~ 5a 0 ~ 3.4a 0 ~ 2.5a 0 ~ 2a 0 ~ 1.25a 0 ~ 1.12a 0 ~ 0.63a 25w 30.6w 30w 30w 30w 30.24w 30.24w 80mvp-p 100mvp-p 120mvp-p 120mvp-p 150mvp-p 150mvp-p 250m vp-p 5.0% 4.5 ~ 5.5v can be adjusted by internal potentiometer svr1 8.7 ~ 10.5v 10.8 ~ 13.2v 13.5 ~ 16.5v 21.6 ~ 26.4v 24.3 ~ 29.7v 43.2 ~ 52.8v -25% ~ 3%. can be adjusted by internal potentiometer svr2 1.0% 2.0% 500ms, 80ms / 230vac 10 at full load 00ms, 80ms / 115vac 90 ~ 264vac 127 ~ 370vdc 47 ~ 63hz 75% 80% 82% 82% 85% 85% 87% 5.75 ~ 6.75v 11 ~ 13.5v 13.8 ~ 16v 17.5 ~ 21v 28 ~ 32v 31 ~ 36.4v 54 ~ 60v 0.75a/115vac 0.48a/230vac cold start 60a/230vac 0.25ma / 240vac 95 ~ 110% protection type : constant current limiting, recovers automatical ly after fault condition is removed compliance to en55022 (cispr22) class b, en61000-3-2 class a, en610 00-3-3 compliance to en61000-4-2,3,4,5,6,8,11, en55024, light indust ry level, criteria a -20 ~ +60 (refer to "derating curve") 1.1 ~ 10vdc or pwm signal : 100hz ~ 3khz 20 ~ 90% rh non-condensing -40 ~ +80 , 10 ~ 95% rh 0.03%/ (0 ~ 50 ) 10 ~ 500hz, 2g 10min./1cycle, period for 60min. each along x, y, z axes 628.3khrs min. mil-hdbk-217f (25 ) 145*47*30mm (l*w*h) 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. derating may be needed under low input voltage. please check the static ch aracteristics for more details. 5. the power supply is considered as a component that will be operated in comb ination with final equipment. since emc performance will be affected by t he complete installation, the final equipment manufacturers must re- qualify emc directive on the complete installation again. 6. length of set up time is measured at first cold start. turning on/off the pow er supply may lead to increase of the set up time. 7. constant current operation region is within the specified output vol tage range above. this is the suitable operation region for led related app lications. 8. the unit might not be suitable for lighting applications in eu countrie s. please check with your local authorities for the possible use of the unit. 0.26kg; 60pcs/16.6kg/1.25cuft protection type : shut down o/p voltage, re-power on to recover 30w single output switching power supply universal ac input / full rangeprotections: short circuit / over current / over voltage cooling by free air convection built-in constant current limiting circuit with adjustable ocp level optional dimming function : 1.1~10vdc (d type) or pwm (p type) controlled fully isolated plastic case with ip64 level class 2 power unit pass lps suitable for led lighting and moving sign applications (note.8) 100% full load burn-in test low cost 2 years warranty class power unit, no fg features : e l n - 3 0 s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 environment safety & function emc protection 50ms/230vac 16ms/115vac at full load withstand voltage isolation resistance i/p-o/p:3kvac ul1310, can/csa c22.2 no. 223-m91(except for 48v), ip64 approved ; des ign refer to tuv en60950-1 i/p-o/p:>100m ohms / 500vdc / 25 / 70% rh file name:eln-30-spec 2012-03-20 led operation voltage note.7 3 ~ 5v ip64 ( for 48v only) ( except for 48v ) lps emc immunity emc emission
mechanical specification file name:eln-30-spec 2012-03-20 case no.964a unit:mm 30 fosc : 60khz detection pwm circuit o.l.p. emi filter rectifiers power switching filter & rectifiers +v -v dim- dim+ optional dimming control pwm or 1.1~10v i/p control o.v.p. & o.c.p. 320 20 svt 18awg 2c 9.83 +v(red) -v(black) 320 20 svt 18awg 2c 4.38 145 47 2-r2.25 4.38 9.83 ac/l(brown) ac/n(blue) block diagram 63.5 t case 15 t case: max. case temperature. +v(red) dim+(blue) -v(black) dim-(white) output(with optional dimming function) ul2464 18awg 4c 30w single output switching power supply e l n - 3 0 s e r i e s load (%) -15 -5 0 15 30 20 40 60 80 100 input voltage (v) 60hz 90 100 125 135 145 155 165 175 180 200 230 264 100 90 80 70 60 50 40 load (%) derating curve load (%) 0 40 50 derating curve static characteristics ambient temperature ( ) load (%) -20 60 175 load (%) (horizontal) svr2 svr1 output voltage and current adjustment : remove the upper case and adjust th rough svr1 & svr2 shown in the diagram. output voltage adjustment output current adjustment svr1 svr2
dimming control (optional) vdc: 1.1~10v vdc (2)pwm (p type, & : eln-30- + dim+ f t1 t1 t1+t2 f: 100hz ~ 3khz duty= ,0 ~ 100% t2 v f dim- (1)1.1~10v (d type, & : eln-30- lo:0v hi:10v 0 0% 1.1 11% 15% 27.5% 37.5% 60% 77.5% 87.5% 95% 2 20% 3 30% 4 40% 5 50% 6 60% 7 70% 8 80% 9 90% 10 100% dc input duty cycle output current output current 10% 10% 0% 0% 20% 20% 30% 30% 40% 40% 50% 50% 60% 60% 70% 70% 80% 80% 90% 90% 100% 100% 5% 47.5% 30w single output switching power supply e l n - 3 0 s e r i e s file name:eln-30-spec 2012-03-20 level of output current can be adjusted through the dimming control funct ion. when there is no signal sending to the control wires (open circuit between th e two control wires), the power supply unit will operate as 0v (d-type) or 0% duty (p-type) of input signal and hence t he output current will be zero. 12 d) 12 p)
|
